Gaining Access
- TPA16 is the GND
- TPA15 is the device’s RX pin - Connect this to your UART client’s TX
- TPA8 is the device’s TX pin - Connect this to your UART client’s RX
On Power On
*-boot0 version : 4.0.0
fel_flag = 0x00000000
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
DRAM DRIVE INFO: V1.7
DRAM Type =3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM zq value: 00003bbbDRAM CLK =552 MHZ
ID CHECK VERSION: V0.1
using ic R16
USE PLL DDR1
USE PLL NORMAL
PLL FREQUENCE = 1104 MHZ
DRAM PLL DDR1 frequency extend open !
DRAM master priority setting ok.
Auto calculate timing parameter!
para_dram_tpr0 = 0047214f
para_dram_tpr1 = 01c2294b
para_dram_tpr2 = 00061043
tcl = 6,tcwl = 4
DRAM TIMING PARA0 = 0b0e180b
DRAM TIMING PARA1 = 0003040f
DRAM TIMING PARA2 = 0406050a
DRAM TIMING PARA3 = 0000400c
DRAM TIMING PARA4 = 05020405
DRAM TIMING PARA5 = 05050403
DRAM TIMING PARA8 = 90003310
DRAM PHY INTERFACE PARA = 02040102
DRAM VTC is disable
DRAM dynamic DQS/DQ ODT is on
DRAM DQS gate is PD mode.
DRAM one rank training is on,the value is 91003587
DRAM work mode register value = 004318e4
DRAM SIZE =512 M
set one rank ODTMAP
DRAM simple test OK.
dram size =512
card boot number = 2
card no is 2
sdcard 2 line count 4
[mmc]: mmc driver ver 2015-04-13 15:56:39
[mmc]: ***Try SD card 2***
[mmc]: mmc 2 cmd 8 err 00000100
[mmc]: mmc 2 cmd 8 err 00000100
[mmc]: mmc 2 send if cond failed
[mmc]: mmc 2 cmd 55 err 00000100
[mmc]: mmc 2 cmd 55 err 00000100
[mmc]: mmc 2 send app cmd failed
[mmc]: ***Try MMC card 2***
[mmc]: mmc re-update_phase
[mmc]: mmc re-update_phase
[mmc]: 4bit bus ddr!!!
[mmc]: mmc re-update_phase
[mmc]: MMC ver 5.0
[mmc]: SD/MMC Card: 4bit, capacity: 3776MB
[mmc]: vendor: Man 00110100 Snr 025e3285
[mmc]: product: 004GA
[mmc]: revision: 3.0
[mmc]: ***SD/MMC 2 init OK!!!***
sdcard 2 init ok
The size of uboot is 000c0000.
sum=c77486de
src_sum=c77486de
set_mmc_para,sdly 50M 0
set_mmc_para,sdly 25M 0
Succeed in loading uboot from sdmmc flash.
Ready to disable icache.
Jump to secend Boot.
[ 0.340]U-Boot 2011.09-rc1-dirty (Mar 25 2020 - 20:45:43) Allwinner Technology
normal or secure os
pmbus: ready
PMU: AXP221
BOOT_POWER22_POK_SET: 59
BOOT_POWER22_POK_SET: 1
PMU: AXP22x found
bat_vol=2, ratio=100
PMU: dcdc3 1240
PMU: pll1 1008 Mhz,PLL6=600 Mhz
AXI=336 Mhz,AHB=200 Mhz, APB1=100 Mhz
set power on vol to default
dcdc1_vol = 3300
dcdc2_vol = 1100
dcdc3_vol = 1240
dcdc5_vol = 1500
aldo1_vol = 3300
aldo2_vol = 2500
aldo3_vol = 3000
find power_sply to end
vbus not exist
vbus dc exist, limit to dc
fel key old mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
DRAM: 512 MiB
relocation Offset is: 1b00c000
save config for small mem_size
smcl's set manager is NULL
workmode = 0
MMC: 2
sunxi flash init ok
[ 0.798]board_status_probe
[ 0.801]boot_reason init from pmic, set to env: 0x0
[ 0.806]boot reason=0x0, is boot from poweroff
[ 0.811]recovery detect id val: 0
[ 0.814]usb vbus gpio fd: 1386422328
[ 0.818]usb vbus cable not connectted
[ 0.822]board_check_vbus2boot = 0
[ 0.825]axp_probe_key loop: 499
[ 0.840]axp_probe_key loop: 498
[ 0.854]axp_probe_key loop: 497
[ 0.868]axp_probe_key loop: 496
[ 0.882]axp_probe_key loop: 495
[ 0.896]axp_probe_key loop: 494
[ 0.910]axp_probe_key loop: 493
[ 0.924]axp_probe_key loop: 492
[ 0.938]axp_probe_key loop: 491
[ 0.952]axp_probe_key loop: 490
[ 0.966]axp_probe_key loop: 489
[ 0.980]axp_probe_key loop: 488
[ 0.994]axp_probe_key loop: 487
[ 1.008]axp_probe_key loop: 486
[ 1.022]axp_probe_key loop: 485
[ 1.036]axp_probe_key loop: 484
[ 1.050]axp_probe_key loop: 483
[ 1.064]axp_probe_key loop: 482
[ 1.078]axp_probe_key loop: 481
[ 1.092]axp_probe_key loop: 480
[ 1.106]axp_probe_key loop: 479
[ 1.120]axp_probe_key loop: 478
[ 1.134]axp_probe_key loop: 477
[ 1.148]axp_probe_key loop: 476
[ 1.162]axp_probe_key loop: 475
[ 1.176]axp_probe_key loop: 474
[ 1.190]axp_probe_key loop: 473
[ 1.204]axp_probe_key loop: 472
[ 1.218]axp_probe_key loop: 471
[ 1.232]axp_probe_key loop: 470
[ 1.246]axp_probe_key loop: 469
[ 1.260]axp_probe_key loop: 468
[ 1.274]axp_probe_key loop: 467
[ 1.288]axp_probe_key loop: 466
[ 1.302]axp_probe_key loop: 465
[ 1.316]axp_probe_key loop: 464
[ 1.330]axp_probe_key loop: 463
[ 1.344]axp_probe_key loop: 462
[ 1.358]axp_probe_key loop: 461
[ 1.372]axp_probe_key loop: 460
[ 1.386]axp_probe_key loop: 459
[ 1.400]axp_probe_key loop: 458
[ 1.414]axp_probe_key loop: 457
[ 1.428]axp_probe_key loop: 456
[ 1.442]axp_probe_key loop: 455
[ 1.456]axp_probe_key loop: 454
[ 1.470]axp_probe_key loop: 453
[ 1.484]axp_probe_key loop: 452
[ 1.498]axp_probe_key loop: 451
[ 1.512]axp_probe_key loop: 450
[ 1.526]axp_probe_key loop: 449
[ 1.540]axp_probe_key loop: 448
[ 1.554]axp_probe_key loop: 447
[ 1.568]axp_probe_key loop: 446
[ 1.582]axp_probe_key loop: 445
[ 1.596]axp_probe_key loop: 444
[ 1.610]axp_probe_key loop: 443
[ 1.624]axp_probe_key loop: 442
[ 1.638]axp_probe_key loop: 441
[ 1.652]axp_probe_key loop: 440
[ 1.666]axp_probe_key loop: 439
[ 1.680]axp_probe_key loop: 438
[ 1.694]axp_probe_key loop: 437
[ 1.708]axp_probe_key loop: 436
[ 1.722]axp_probe_key loop: 435
[ 1.736]axp_probe_key loop: 434
[ 1.750]axp_probe_key loop: 433
[ 1.764]axp_probe_key loop: 432
[ 1.778]axp_probe_key loop: 431
[ 1.792]axp_probe_key loop: 430
[ 1.806]axp_probe_key loop: 429
[ 1.820]axp_probe_key loop: 428
[ 1.834]axp_probe_key loop: 427
[ 1.848]axp_probe_key loop: 426
[ 1.862]axp_probe_key loop: 425
[ 1.876]axp_probe_key loop: 424
[ 1.890]axp_probe_key loop: 423
[ 1.904]axp_probe_key loop: 422
[ 1.918]axp_probe_key loop: 421
[ 1.932]axp_probe_key loop: 420
[ 1.946]axp_probe_key loop: 419
[ 1.960]axp_probe_key loop: 418
[ 1.974]axp_probe_key loop: 417
[ 1.988]axp_probe_key loop: 416
[ 2.002]axp_probe_key loop: 415
[ 2.016]axp_probe_key loop: 414
[ 2.030]axp_probe_key loop: 413
[ 2.044]axp_probe_key loop: 412
[ 2.058]axp_probe_key loop: 411
[ 2.072]axp_probe_key loop: 410
[ 2.086]axp_probe_key loop: 409
[ 2.100]axp_probe_key loop: 408
[ 2.114]axp_probe_key loop: 407
[ 2.128]axp_probe_key loop: 406
[ 2.142]axp_probe_key loop: 405
[ 2.156]axp_probe_key loop: 404
[ 2.170]axp_probe_key loop: 403
[ 2.184]axp_probe_key loop: 402
[ 2.198]axp_probe_key loop: 401
[ 2.212]axp_probe_key loop: 400
[ 2.226]axp_probe_key loop: 399
[ 2.240]axp_probe_key loop: 398
[ 2.254]axp_probe_key loop: 397
[ 2.268]axp_probe_key loop: 396
[ 2.282]axp_probe_key loop: 395
[ 2.296]axp_probe_key loop: 394
[ 2.310]axp_probe_key loop: 393
[ 2.324]axp_probe_key loop: 392
[ 2.338]axp_probe_key loop: 391
[ 2.352]axp_probe_key loop: 390
[ 2.366]axp_probe_key loop: 389
[ 2.380]axp_probe_key loop: 388
[ 2.394]axp_probe_key loop: 387
[ 2.408]axp_probe_key loop: 386
[ 2.422]axp_probe_key loop: 385
[ 2.436]axp_probe_key loop: 384
[ 2.450]axp_probe_key loop: 383
[ 2.464]axp_probe_key loop: 382
[ 2.478]axp_probe_key loop: 381
[ 2.492]axp_probe_key loop: 380
[ 2.506]axp_probe_key loop: 379
[ 2.520]axp_probe_key loop: 378
[ 2.534]axp_probe_key loop: 377
[ 2.548]axp_probe_key loop: 376
[ 2.562]axp_probe_key loop: 375
[ 2.576]axp_probe_key loop: 374
[ 2.590]axp_probe_key loop: 373
[ 2.604]axp_probe_key loop: 372
[ 2.618]axp_probe_key loop: 371
[ 2.632]axp_probe_key loop: 370
[ 2.646]axp_probe_key loop: 369
[ 2.660]axp_probe_key loop: 368
[ 2.674]axp_probe_key loop: 367
[ 2.688]axp_probe_key loop: 366
[ 2.702]axp_probe_key loop: 365
[ 2.716]axp_probe_key loop: 364
[ 2.730]axp_probe_key loop: 363
[ 2.744]axp_probe_key loop: 362
[ 2.758]axp_probe_key loop: 361
[ 2.772]axp_probe_key loop: 360
[ 2.786]axp_probe_key loop: 359
[ 2.800]axp_probe_key loop: 358
[ 2.814]axp_probe_key loop: 357
[ 2.828]axp_probe_key loop: 356
[ 2.842]axp_probe_key loop: 355
[ 2.856]axp_probe_key loop: 354
[ 2.870]axp_probe_key loop: 353
[ 2.884]axp_probe_key loop: 352
[ 2.898]axp_probe_key loop: 351
[ 2.912]axp_probe_key loop: 350
[ 2.926]axp_probe_key loop: 349
[ 2.940]axp_probe_key loop: 348
[ 2.954]axp_probe_key loop: 347
[ 2.968]axp_probe_key loop: 346
[ 2.982]axp_probe_key loop: 345
[ 2.996]axp_probe_key loop: 344
[ 3.010]axp_probe_key loop: 343
[ 3.024]axp_probe_key loop: 342
[ 3.038]axp_probe_key loop: 341
[ 3.052]axp_probe_key loop: 340
[ 3.066]axp_probe_key loop: 339
[ 3.080]axp_probe_key loop: 338
[ 3.094]axp_probe_key loop: 337
[ 3.108]axp_probe_key loop: 336
[ 3.122]axp_probe_key loop: 335
[ 3.136]axp_probe_key loop: 334
[ 3.150]axp_probe_key loop: 333
[ 3.164]axp_probe_key loop: 332
[ 3.178]axp_probe_key loop: 331
[ 3.192]axp_probe_key loop: 330
[ 3.206]axp_probe_key loop: 329
[ 3.220]axp_probe_key loop: 328
[ 3.234]axp_probe_key loop: 327
[ 3.248]axp_probe_key loop: 326
[ 3.262]axp_probe_key loop: 325
[ 3.276]axp_probe_key loop: 324
[ 3.290]axp_probe_key loop: 323
[ 3.304]axp_probe_key loop: 322
[ 3.318]axp_probe_key loop: 321
[ 3.332]axp_probe_key loop: 320
[ 3.346]axp_probe_key loop: 319
[ 3.360]axp_probe_key loop: 318
[ 3.374]axp_probe_key loop: 317
[ 3.388]axp_probe_key loop: 316
[ 3.402]axp_probe_key loop: 315
[ 3.416]AP boot into normal mode
In: serial
Out: serial
Err: serial
--------fastboot partitions--------
-total partitions:9-
-name- -start- -size-
boot-res : 1000000 800000
env : 1800000 1000000
app : 2800000 4000000
recovery : 6800000 20000000
system_a : 26800000 20000000
system_b : 46800000 20000000
Download : 66800000 21000000
reserve : 87800000 1000000
UDISK : 88800000 0
-----------------------------------
Loading file "./rockrobo/dram.size" from mmc device 2:1
** File not found ./rockrobo/dram.size
unable to open file ./rockrobo/dram.size
base bootcmd=run setargs_mmc boot_normal
bootcmd set setargs_mmc
Loading file "roborock.conf" from mmc device 2:6
32 bytes read
language:language=en
flag_recovery: 0x0
flag_command:
flag_restore_default:
flag_bootB:0x4
flag_bootA:0x1
upgrade stage:0x63
No upgradeover system found, check if has normal system, pmu: 0x0
board_common.c:check_android_misc:will be boot A system
to be run cmd=run setargs_mmc boot_normal
boot A system
WORK_MODE_BOOT
[ 3.531]Hit any key to stop autoboot: 0
Loading file "/boot/zImage" from mmc device 2:8
3882616 bytes read
[ 3.635]para err in disp_ioctl, cmd = 0xa,screen id = 1
reload config to 0x43000000
[ 3.687]Starting kernel ...
[ 3.687]enable watchdog 1c20cb8 value 0xb1(16s)
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.4.39 (rockrobo@apimg) (gcc version 4.8.4 (Ubuntu/Linaro 4.8.4-2ubuntu1~14.04.1) ) #1 SMP PREEMPT Wed Mar 25 20:47:59 CST 2020
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: sun8i
[ 0.000000] cma: CMA: reserved 96 MiB at 5a000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] script_init enter!
[ 0.000000] script_init exit!
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c0cec000 s10752 r8192 d13824 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: rootwait boot_fs=a console=ttyS0,115200 root=/dev/mmcblk0p8 rootfstype=ext4 loglevel=7 partitions=boot-res@mmcblk0p2:env@mmcblk0p5:app@mmcblk0p6:recovery@mmcblk0p7:system_a@mmcblk0p8:system_b@mmcblk0p9:Download@mmcblk0p10:reserve@mmcblk0p11:UDISK@mmcblk0p1 boot_reason=0x0 location=en boot_ver=2011.09-rc1-dirty
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 411968k/411968k available, 112320k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0755628 (7478 kB)
[ 0.000000] .init : 0xc0756000 - 0xc079ba00 ( 279 kB)
[ 0.000000] .data : 0xc079c000 - 0xc07fcea0 ( 388 kB)
[ 0.000000] .bss : 0xc07fe098 - 0xc0858180 ( 361 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:416
[ 0.000000] try to syncboot of clk ats
[ 0.000000] try to syncboot of clk sdmmc2mod
[ 0.000000] try to syncboot of clk uart0
[ 0.000000] try to syncboot of clk pll_ddr1
[ 0.000000] try to syncboot of clk debe0
[ 0.000000] try to syncboot of clk dma
<6>[ 0.000000] try to syncboot of clk sat
[ 0.000000] try to syncboot of clk pio
[ 0.000000] try to syncboot of clk mbus
[ 0.000000] try to syncboot of clk drc0
[ 0.000000] try to syncboot of clk lvds
[ 0.000000] try to syncboot of clk axi
[ 0.000000] Architected local timer running at 24.00MHz.
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000240] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
[ 0.000268] pid_max: default: 32768 minimum: 301
[ 0.000581] Mount-cache hash table entries: 512
[ 0.001641] Initializing cgroup subsys debug
[ 0.001661] Initializing cgroup subsys cpuacct
[ 0.001674] Initializing cgroup subsys freezer
[ 0.001719] CPU: Testing write buffer coherency: ok
[ 0.001777] ftrace: allocating 19622 entries in 58 pages
[ 0.030304] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.030325] [sunxi_smp_prepare_cpus] enter
[ 0.030374] Setting up static identity map for 0x4050d630 - 0x4050d688
[ 0.010000] CPU1: Booted secondary processor
[ 0.010000] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.010000] CPU2: Booted secondary processor
[ 0.010000] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.010000] CPU3: Booted secondary processor
[ 0.010000] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.210233] Brought up 4 CPUs
[ 0.210253] SMP: Total of 4 processors activated (19200.00 BogoMIPS).
[ 0.210550] devtmpfs: initialized
[ 0.214326] pinctrl core: initialized pinctrl subsystem
[ 0.214326] dummy:
[ 0.223873] NET: Registered protocol family 16
[ 0.241807] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[ 0.241912] script_sysfs_init success
[ 0.242210] sunxi pinctrl probe enter
[ 0.242910] gpiochip_add: registered GPIOs 0 to 383 on device: sunxi-pinctrl
[ 0.243986] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
[ 0.244183] axp_pinctrl_probe enter...
[ 0.244334] gpiochip_add: registered GPIOs 1024 to 1029 on device: axp-pinctrl
[ 0.244357] mainkey total count : 77
[ 0.244398] map mainkey [motor_para] to pinctrl, map number [2]
[ 0.244463] axp pinctrl driver probe ok
[ 0.245505] [sunxi-module]: [sunxi-module.0] probe success
[ 0.245550] script config pll3 to 297 Mhz
[ 0.245567] script config pll4 to 300 Mhz
[ 0.245603] script config pll6 to 600 Mhz
[ 0.245618] script config pll8 to 408 Mhz
[ 0.245641] script config pll9 to 480 Mhz
[ 0.245656] script config pll10 to 297 Mhz
[ 0.245665] sunxi_default_clk_init
[ 0.245674] try to set pll6ahb1 to 200000000
[ 0.245727] try to set ahb clk source to pll6ahb1
[ 0.245737] set ahb clk source to pll6ahb1
[ 0.245757] set apb2 to low freq 1.2 Mhz
[ 0.245786] set ahb clk source to pll6
[ 0.245796] recove apb2 to pre freq 24000000
[ 0.245811] try to set ahb1 to 200000000
[ 0.245824] try to set apb1 to 100000000
[ 0.245841] script config apb2 to 37 Mhz
[ 0.250929] bio: create slab <bio-0> at 0
[ 0.250929] [ARISC] :sunxi-arisc driver v1.60
[ 0.288229] [ARISC] :arisc version: [v0.0.76]
[ 0.288244] [sunxi-module]: arisc register success
[ 0.507529] [ARISC] :sunxi-arisc driver v1.60 startup succeeded
[ 0.510548] SCSI subsystem initialized
[ 0.510694] usbcore: registered new interface driver usbfs
[ 0.510771] usbcore: registered new interface driver hub
[ 0.510815] usbcore: registered new device driver usb
[ 0.510815] twi_chan_cfg()350 - [twi0] has no twi_regulator.
[ 0.510815] twi_chan_cfg()350 - [twi1] has no twi_regulator.
[ 0.510815] twi_chan_cfg()350 - [twi2] has no twi_regulator.
[ 0.510815] Linux video capture interface: v2.00
[ 0.510041] axp22_board axp22_board: AXP (CHIP ID: 0x06) detected
[ 0.511814] axp22_dcdc1: 1600 <--> 3400 mV at 3300 mV
[ 0.511814] axp22_dcdc2: 600 <--> 1540 mV at 1100 mV
[ 0.511814] axp22_dcdc3: 600 <--> 1860 mV at 1240 mV
[ 0.511814] axp22_dcdc4: 600 <--> 1540 mV at 1100 mV
[ 0.511814] axp22_dcdc5: 1000 <--> 2550 mV at 1500 mV
[ 0.511814] axp22_rtc: 3000 mV
[ 0.511814] axp22_aldo1: 700 <--> 3300 mV at 3300 mV
[ 0.511814] axp22_aldo2: 700 <--> 3300 mV at 2500 mV
[ 0.511814] axp22_aldo3: 700 <--> 3300 mV at 3000 mV
[ 0.511814] axp22_dldo1: 700 <--> 3300 mV at 700 mV
[ 0.511814] axp22_dldo2: 700 <--> 3300 mV at 700 mV
[ 0.511814] axp22_dldo3: 700 <--> 3300 mV at 700 mV
[ 0.520139] axp22_dldo4: 700 <--> 3300 mV at 700 mV
[ 0.520222] axp22_eldo1: 700 <--> 3300 mV at 700 mV
[ 0.520222] axp22_eldo1: supplied by axp22_dcdc1
[ 0.520296] axp22_eldo2: 700 <--> 3300 mV at 700 mV
[ 0.520296] axp22_eldo2: supplied by axp22_dcdc1
[ 0.520296] axp22_eldo3: 700 <--> 3300 mV at 700 mV
[ 0.520296] axp22_eldo3: supplied by axp22_dcdc1
[ 0.520296] axp22_dc5ldo: 700 <--> 1400 mV at 1100 mV
[ 0.520296] axp22_ldoio0: 700 <--> 3300 mV at 3800 mV
[ 0.520296] axp22_ldoio1: 700 <--> 3300 mV at 3800 mV
[ 0.520296] axp22_dc1sw: at 700 mV
[ 0.520296] axp22_dc1sw: supplied by axp22_dcdc1
[ 0.520434] input: axp22-supplyer as /devices/platform/axp22_board/axp22-supplyer.20/input/input0
[ 0.520733] now_rest_vol = 0
[ 0.520733] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.521114] cfg80211: Calling CRDA to update world regulatory domain
[ 0.521178] Switching to clocksource arch_sys_counter
[ 0.535652] FS-Cache: Loaded
[ 0.535992] CacheFiles: Loaded
[ 0.546665] [usb_manager]: CONFIG_USB_SUNXI_USB0_OTG
[ 0.546704] get usbc0(usb_restrict pin) failed
[ 0.547115] [sw_udc]: udc_init: version 20080411
[ 0.547724] [ddrfreq] dram_clk value is 552
[ 0.547736] [ddrfreq] sunxi_ddrfreq_max=552000
[ 0.547747] [ddrfreq] dram_type value is 3
[ 0.547758] [ddrfreq] dram_zq value is 0x3bbb
[ 0.547768] [ddrfreq] dram_odt_en value is 1
[ 0.547779] [ddrfreq] dram_para1 value is 0x10f20200
[ 0.547790] [ddrfreq] dram_para2 value is 0x0
[ 0.547800] [ddrfreq] dram_mr0 value is 0x1c70
[ 0.547811] [ddrfreq] dram_mr1 value is 0x40
[ 0.547821] [ddrfreq] dram_mr2 value is 0x18
[ 0.547832] [ddrfreq] dram_mr3 value is 0x0
[ 0.547842] [ddrfreq] dram_tpr0 value is 0x47214f
[ 0.547853] [ddrfreq] dram_tpr1 value is 0x1c2294b
[ 0.547865] [ddrfreq] dram_tpr2 value is 0x61043
[ 0.547875] [ddrfreq] dram_tpr3 value is 0x0
[ 0.547886] [ddrfreq] dram_tpr4 value is 0x0
[ 0.547896] [ddrfreq] dram_tpr5 value is 0x0
[ 0.547906] [ddrfreq] dram_tpr6 value is 0x0
[ 0.547917] [ddrfreq] dram_tpr7 value is 0x0
[ 0.547927] [ddrfreq] dram_tpr8 value is 0x0
[ 0.547938] [ddrfreq] dram_tpr9 value is 0x0
[ 0.547948] [ddrfreq] dram_tpr10 value is 0x0
[ 0.547959] [ddrfreq] dram_tpr11 value is 0x0
[ 0.547970] [ddrfreq] dram_tpr12 value is 168
[ 0.547979] [ddrfreq] sunxi_ddrfreq_min=168000
[ 0.547990] [ddrfreq] dram_tpr13 value is 0x10901
[ 0.548175] [dsm] use sysconfig
[ 0.548185] [dsm] -----------Dram scene-freq Table------------
[ 0.548197] [dsm] scene = 0 frequency = 552000KHz
[ 0.548208] [dsm] scene = 1 frequency = 360000KHz
[ 0.548218] [dsm] scene = 2 frequency = 240000KHz
[ 0.548229] [dsm] scene = 3 frequency = 168000KHz
[ 0.548238] [dsm] --------------------------------------------
[ 0.548365] [ddrfreq] LV_count value is 3
[ 0.548389] [ddrfreq] ---------------Dram V-F Table---------------
[ 0.548402] [ddrfreq] voltage = 1100mv frequency = 552000KHz
[ 0.548413] [ddrfreq] voltage = 1100mv frequency = 360000KHz
[ 0.548424] [ddrfreq] voltage = 1100mv frequency = 0KHz
[ 0.548434] [ddrfreq] --------------------------------------------
[ 0.548583] [ddrfreq] last_vdd=1100
[ 0.548661] [ddrfreq] __sram_start: 0xc07fd000, __sram_end: 0xc07fe074, __sram_text_start: 0xf0000000, __sram_data_end: 0xf0001074
[ 0.548677] [ddrfreq] sunxi dramfreq probe ok!
[ 0.549021] NET: Registered protocol family 2
[ 0.549347] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.549992] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.550308] TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
[ 0.550569] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.550582] TCP: reno registered
[ 0.550598] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.550626] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.550965] NET: Registered protocol family 1
[ 0.551406] RPC: Registered named UNIX socket transport module.
[ 0.551422] RPC: Registered udp transport module.
[ 0.551432] RPC: Registered tcp transport module.
[ 0.551442] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.551892] [pm]aw_pm_init!
[ 0.551907] standby_mode = 1.
[ 0.551917] wakeup src cnt is : 1.
[ 0.551929] [exstandby]leave extended_standby_enable_wakeup_src : event 0x2000
[ 0.551942] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x80
[ 0.551955] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x0
[ 0.551969] sunxi_reg_init enter
[ 0.555421] NTFS driver 2.1.30 [Flags: R/W].
[ 0.555641] fuse init (API version 7.18)
[ 0.556130] msgmni has been set to 996
[ 0.557884] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.557905] io scheduler noop registered
[ 0.557916] io scheduler deadline registered
[ 0.558022] io scheduler cfq registered (default)
[ 0.558439] pwm module init!
[ 0.559019] sw_uart_get_devinfo()1476 - uart0 has no uart_regulator.
[ 0.559040] sw_uart_get_devinfo()1476 - uart1 has no uart_regulator.
[ 0.559056] sw_uart_get_devinfo()1476 - uart2 has no uart_regulator.
[ 0.559599] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[ 0.559623] sw_console_setup()1236 - console setup baud 115200 parity n bits 8, flow n
[ 0.559648] sw_uart_set_termios()692 - sw_uart_set_termios:uart0 set baudrate: 115200, real baud is 117187
[ 0.595951] axp22_mfd_irq_work: 4000020000:600080cf6c
[ 0.596299] axp22_mfd_irq_work: 20000:600080cf6c
[ 0.709424] console [ttyS0] enabled
[ 0.709795] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI
[ 0.710119] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI
[ 0.714853] loop: module loaded
[ 0.715037] [MCU_UART] sent ap resume event to mcu
[ 0.715237] TIMER1_INTVAL_REG = 5dc
[ 0.715408] jiffies initialized success
[ 0.715416] [lds]: lds_module_init module init!
[ 0.715595] [lds]: lds_motor_probe
[ 0.716089] input: lds_input as /devices/virtual/input/input1
[ 0.716164] [wifi_pm]: select wifi: rtl8189es !!
[ 0.716325] [rtl8189es]: exec rtl8189es_wifi_gpio_init
[ 0.716336] [rtl8189es]: module power name axp22_dldo1
[ 0.716345] [rtl8189es]: module power ext1 name axp22_dldo2
[ 0.716354] [rtl8189es]: failed to fetch wifi_power_ext2
[ 0.716364] [rtl8189es]: use wifi card shutdown pin
[ 0.716371] [rtl8189es]: rtl8189es module power set by axp.
[ 0.716471] [rtl8189es]: first time
[ 0.803493] [rtl8189es]: regulator on.
[ 1.996218] [rtl8189es]: gpio rtl8189es_shdn set val 0, act val 0
[ 2.002915] [wifi_pm]: wifi gpio init is OK !!
[ 2.007806] module init!
[ 2.010597] [hwinfo]: hwinfo_mod_init E
[ 2.014790] [hwinfo]: 0, 0
[ 2.017746] [hwinfo]: 2, 0
[ 2.020922] tun: Universal TUN/TAP device driver, 1.6
[ 2.026437] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.033431] PPP generic driver version 2.4.2
[ 2.038287] PPP BSD Compression module registered
[ 2.043519] PPP Deflate Compression module registered
[ 2.049912] PPP MPPE Compression module registered
[ 2.055169] NET: Registered protocol family 24
[ 2.060067] [sw_hcd0]: usb host driver initialize........
[ 2.066055] [sw_hcd0]: open_usb_clock
[ 2.070158] get usb_regulator id vbus is nocare
[ 2.075099] [sunxi_hcd0]: host_init_state = 0
[ 2.079849] [sw_hcd0]: platform is usb host
[ 2.084481] [sw_hcd0]: sunxi_hcd_init_controller: sunxi_hcd_host0: USB Host mode controller at f1c19000 using PIO, IRQ 103
[ 2.096566] sunxi_hcd_host0 sunxi_hcd_host0: sunxi_hcd host driver
[ 2.103329] sunxi_hcd_host0 sunxi_hcd_host0: new USB bus registered, assigned bus number 1
[ 2.113108] hub 1-0:1.0: USB hub found
[ 2.117214] hub 1-0:1.0: 1 port detected
[ 2.121928] [sw_hcd0]: sunxi_usb_host0_disable start
[ 2.127350] [sw_hcd0]: sunxi_hcd_wait_for_disconnect cnt=0
[ 2.133360] [sunxi_hcd_host0]: Set USB Power OFF
[ 2.138400] -------sunxi_hcd0_soft_disconnect---------
[ 2.143343] wrn: hcd is not enable, need not stop hcd
[ 2.149529] [sunxi_hcd_host0]: Set USB Power OFF
[ 2.154605] [sw_hcd0]: close_usb_clock
[ 2.158715] [sw_hcd0]: sunxi_usb_host0_disable end
[ 2.164743] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
[ 2.172126] sunxi cedar version 0.1
[ 2.176071] [cedar]: install start!!!
[ 2.180291] [cedar]: install end!!!
[ 2.188001] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0
[ 2.195078] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->start 0x01c20ca0, res->end 0x01c20cbf
[ 2.206131] sunxi wdt request irq 57 ok
[ 2.210527] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0)
[ 2.217649] [boot_reason]: br_wdt_check entry
[ 2.222602] sunxi wdt start in uboot
[ 2.227053] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 2.236589] autohotplug_init init ok
[ 2.240541] sunxi_cpufreq_initcall: clocks pll=1008000000,cpu=1008000000,axi=336000000
[ 2.249185] cur: pll=1008000000, cpudiv=1, axidiv=3
[ 2.254536] axp22_dcdc3: Failed to create debugfs directory
[ 2.260647] sunxi_cpufreq_initcall, get cpu frequency from sysconfig, max freq: 1200MHz, min freq: 648MHz
[ 2.271132] -------------------CPU V-F Table--------------------
[ 2.277684] frequency = 1536000KHz voltage = 1500mv
[ 2.283211] frequency = 1344000KHz voltage = 1460mv
[ 2.288722] frequency = 1200000KHz voltage = 1360mv
[ 2.294243] frequency = 1008000KHz voltage = 1240mv
[ 2.299752] frequency = 816000KHz voltage = 1140mv
[ 2.305181] frequency = 648000KHz voltage = 1140mv
[ 2.310607] frequency = 0KHz voltage = 1120mv
[ 2.315832] frequency = 0KHz voltage = 1120mv
[ 2.321068] -----------------------------------------------------
[ 2.328051] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.117 2015-12-1 14:13) Compiled in Mar 25 2020 at 20:47:21
[ 2.339311] [mmc]: get mmc1's sdc_power failed
[ 2.344195] [mmc]: get mmc2's sdc_power failed
[ 2.349041] [mmc]: get mmc2's 2xmode ok, val = 1
[ 2.354094] [mmc]: get mmc2's ddrmode ok, val = 1
[ 2.359229] [mmc]: MMC host used card: 0x6, boot card: 0x4, io_card 2
[ 2.367789] [mmc]: mmc not poweroff notifiy
[ 2.372415] [mmc]: sdc2 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.383135] [mmc]: sdc2 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.393016] [mmc]: mmc not poweroff notifiy
[ 2.394216] [mmc]: sdc2 power_supply is null
[ 2.402252] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.410047] [mmc]: sdc2 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.425455] usbcore: registered new interface driver usbhid
[ 2.430893] [mmc]: *** sunxi_mci_dump_errinfo(L828): smc 2 err, cmd 52, RTO !!
[ 2.431766] [mmc]: *** sunxi_mci_dump_errinfo(L828): smc 2 err, cmd 52, RTO !!
[ 2.431804] [mmc]: sdc2 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.434313] [mmc]: sdc2 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.436239] [mmc]: *** sunxi_mci_dump_errinfo(L828): smc 2 err, cmd 8, RTO !!
[ 2.436272] *******************Try sdio*******************
[ 2.437104] [mmc]: *** sunxi_mci_dump_errinfo(L828): smc 2 err, cmd 5, RTO !!
[ 2.437954] [mmc]: *** sunxi_mci_dump_errinfo(L828): smc 2 err, cmd 5, RTO !!
[ 2.438804] [mmc]: *** sunxi_mci_dump_errinfo(L828): smc 2 err, cmd 5, RTO !!
[ 2.439654] [mmc]: *** sunxi_mci_dump_errinfo(L828): smc 2 err, cmd 5, RTO !!
[ 2.439686] *******************Try sd *******************
[ 2.440519] [mmc]: *** sunxi_mci_dump_errinfo(L828): smc 2 err, cmd 55, RTO !!
[ 2.441372] [mmc]: *** sunxi_mci_dump_errinfo(L828): smc 2 err, cmd 55, RTO !!
[ 2.442224] [mmc]: *** sunxi_mci_dump_errinfo(L828): smc 2 err, cmd 55, RTO !!
[ 2.443077] [mmc]: *** sunxi_mci_dump_errinfo(L828): smc 2 err, cmd 55, RTO !!
[ 2.443108] *******************Try mmc*******************
[ 2.443122] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.443571] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.443682] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.443789] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.446289] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.481293] [mmc]: sdc2 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.481964] [hwinfo]: 1, 0
[ 2.481973] [hwinfo]: EMMC: 17, 0x34474130
[ 2.493883] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.494031] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing MMC-HS(SDR20) dt B
[ 2.494105] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing MMC-HS(SDR20) dt B
[ 2.494635] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing MMC-HS(SDR20) dt B
[ 2.494840] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing UHS-DDR50 dt B
[ 2.494917] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing UHS-DDR50 dt B
[ 2.495037] mmc0: new high speed DDR MMC card at address 0001
[ 2.495549] mmcblk0: mmc0:0001 004GA0 3.68 GiB
[ 2.495812] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB
[ 2.496038] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB
[ 2.497081] mmcblk0: p1 p2 p3 < p5 p6 p7 p8 p9 p10 p11 >
[ 2.497138] mmcblk0: p1 size 3268608 extends beyond EOD, truncated
[ 2.500411] mmcblk0boot1: unknown partition table
[ 2.501714] mmcblk0boot0: unknown partition table
[ 2.501951] *******************mmc init ok *******************
[ 2.599534] usbhid: USB HID core driver
[ 2.695622] [audiocodec] : aif2 not used!
[ 2.746621] [audiocodec] : aif3 not used!
[ 2.752637] asoc: sndcodec <-> sunxi-codec mapping ok
[ 2.759176] u32 classifier
[ 2.762144] Actions configured
[ 2.765852] Netfilter messages via NETLINK v0.30.
[ 2.771071] nf_conntrack version 0.5.0 (7973 buckets, 31892 max)
[ 2.778036] ctnetlink v0.93: registering with nfnetlink.
[ 2.783898] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 2.791499] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 2.798291] xt_time: kernel timezone is -0000
[ 2.803460] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.809433] arp_tables: (C) 2002 David S. Miller
[ 2.814554] TCP: cubic registered
[ 2.818164] Initializing XFRM netlink socket
[ 2.823144] NET: Registered protocol family 10
[ 2.828911] Mobile IPv6
[ 2.831633] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 2.837692] NET: Registered protocol family 17
[ 2.842573] NET: Registered protocol family 15
[ 2.847421] L2TP core driver, V2.0
[ 2.851154] PPPoL2TP kernel driver, V2.0
[ 2.855428] L2TP IP encapsulation support (L2TPv3)
[ 2.860718] L2TP netlink interface
[ 2.864454] L2TP ethernet pseudowire support (L2TPv3)
[ 2.870178] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 2.878538] ThumbEE CPU extension supported.
[ 2.883215] Registering SWP/SWPB emulation handler
[ 2.889230] axp22_dc5ldo: incomplete constraints, leaving on
[ 2.895713] axp22_aldo3: incomplete constraints, leaving on
[ 2.901853] axp22_aldo2: incomplete constraints, leaving on
[ 2.907975] axp22_aldo1: incomplete constraints, leaving on
[ 2.914114] axp22_rtc: incomplete constraints, leaving on
[ 2.920061] axp22_dcdc5: incomplete constraints, leaving on
[ 2.926183] axp22_dcdc4: incomplete constraints, leaving on
[ 2.932329] axp22_dcdc3: incomplete constraints, leaving on
[ 2.938451] axp22_dcdc2: incomplete constraints, leaving on
[ 2.944588] axp22_dcdc1: incomplete constraints, leaving on
[ 2.950912] [boot_reason]: module init!
[ 2.955109] otg_wakelock_init: No USB transceiver found
[ 2.960857] sunxi-rtc sunxi-rtc: setting system clock to 1970-01-01 00:00:07 UTC (7)
[ 2.969334] ths_fetch_sysconfig_para: type err device_used = 1.
[ 2.975998] ths_fetch_sysconfig_para: type err ths_trip1_3 = 110.
[ 2.982769] ths_fetch_sysconfig_para: type err ths_trip1_4 = 110.
[ 2.989508] ths_fetch_sysconfig_para: type err ths_trip1_5 = 110.
[ 2.996261] ths_fetch_sysconfig_para: type err ths_trip1_6 = 110.
[ 3.003011] ths_fetch_sysconfig_para: type err ths_trip1_7 = 110.
[ 3.009755] ths_fetch_sysconfig_para: type err ths_trip1_3_min = 0.
[ 3.016696] ths_fetch_sysconfig_para: type err ths_trip1_3_max = 0.
[ 3.023638] ths_fetch_sysconfig_para: type err ths_trip1_4_min = 0.
[ 3.030576] ths_fetch_sysconfig_para: type err ths_trip1_4_max = 0.
[ 3.037504] ths_fetch_sysconfig_para: type err ths_trip1_5_min = 0.
[ 3.044472] ths_fetch_sysconfig_para: type err ths_trip1_5_max = 0.
[ 3.051416] ths_fetch_sysconfig_para: type err ths_trip1_6_min = 0.
[ 3.058347] ths_fetch_sysconfig_para: type err ths_trip1_6_max = 0.
[ 3.065288] ths_fetch_sysconfig_para: type err ths_trip2_count = 0.
[ 3.072229] ths_fetch_sysconfig_para: type err ths_trip2_0 = 0.
[ 3.078998] input: sunxi-ths as /devices/virtual/input/input2
[ 3.085722] suxi_ths: Kernel Thermal management registered
[ 3.091734] fetch C0_LV_count from sysconfig failed
[ 3.097528] CPU Budget:Register notifier
[ 3.101830] CPU Budget:register Success
[ 3.106014] sunxi-budget-cooling sunxi-budget-cooling: Cooling device registered: thermal-budget-0
[ 3.119038] ALSA device list:
[ 3.122318] #0: audiocodec
[ 3.125659] sw_uart_startup()603 - ttyS0 start up by swapper/0, pid 1
[ 3.132761] sw_uart_set_termios()692 - sw_uart_set_termios:uart0 set baudrate: 115200, real baud is 117187
[ 3.148585] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: (null)
[ 3.157640] VFS: Mounted root (ext4 filesystem) on device 179:8.
[ 3.165946] devtmpfs: mounted
[ 3.169421] Freeing init memory: 276K
Mount failed for selinuxfs on /sys/fs/selinux: No such file or directory
[ 3.240070] sw_uart_shutdown()635 - ttyS0 shut down by init, pid 1
[ 3.313994] sw_uart_startup()603 - ttyS0 start up by init, pid 79
[ 3.320822] sw_uart_set_termios()692 - sw_uart_set_termios:uart0 set baudrate: 115200, real baud is 117187
[ 3.352090] sw_uart_shutdown()635 - ttyS0 shut down by plymouth-upstar, pid 79
[ 3.406011] init: plymouth-upstart-bridge main process (79) terminated with status 1
[ 3.414763] init: plymouth-upstart-bridge main process ended, respawning
[ 3.428705] sw_uart_startup()603 - ttyS0 start up by init, pid 89
[ 3.435622] sw_uart_set_termios()692 - sw_uart_set_termios:uart0 set baudrate: 115200, real baud is 117187
[ 3.458320] sw_uart_shutdown()635 - ttyS0 shut down by plymouth-upstar, pid 89
[ 3.486228] init: plymouth-upstart-bridge main process (89) terminated with status 1
[ 3.494856] init: plymouth-upstart-bridge main process ended, respawning
[ 3.503862] init: ureadahead main process (82) terminated with status 5
[ 3.518153] sw_uart_startup()603 - ttyS0 start up by init, pid 92
[ 3.524955] sw_uart_set_termios()692 - sw_uart_set_termios:uart0 set baudrate: 115200, real baud is 117187
[ 3.544354] sw_uart_shutdown()635 - ttyS0 shut down by plymouth-upstar, pid 92
[ 3.566103] init: plymouth-upstart-bridge main process (92) terminated with status 1
[ 3.574834] init: plymouth-upstart-bridge main process ended, respawning
[ 3.595515] sw_uart_startup()603 - ttyS0 start up by init, pid 98
[ 3.602299] sw_uart_set_termios()692 - sw_uart_set_termios:uart0 set baudrate: 115200, real baud is 117187
[ 3.661637] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 3.785758] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 3.882416] EXT4-fs (mmcblk0p10): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 3.962677] EXT4-fs (mmcblk0p11): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
* Starting Signal sysvinit that the rootfs is mounted [ OK ]
* Starting Populate /dev filesystem [ OK ]
* Stopping Populate /dev filesystem [ OK ]
* Starting Clean /tmp directory [ OK ]
* Stopping Clean /tmp directory [ OK ]
* Starting Populate and link to /run filesystem [ OK ]
* Stopping Populate and link to /run filesystem [ OK ]
* Stopping Track if upstart is running in a container [ OK ]
* Starting Initialize or finalize resolvconf [ OK ]
* Starting set console keymap [ OK ]
* Starting Signal sysvinit that virtual filesystems are mounted [ OK ]
* Starting Signal sysvinit that virtual filesystems are mounted [ OK ]
* Stopping set console keymap [ OK ]
* Starting Signal sysvinit that remote filesystems are mounted [ OK ]
* Starting Bridge udev events into upstart [ OK ]
* Starting device node and kernel event manager [ OK ]
* Starting load modules from /etc/modules [ OK ]
* Starting cold plug devices [ OK ]
* Starting rockrobo play bootring service [ OK ]
* Starting log initial device creation [ OK ]
* Stopping load modules from /etc/modules [ OK ]
* Starting configure network device security [ OK ]
* Stopping Read required files in advance (for other mountpoints) [ OK ]
* Starting Mount network filesystems [ OK ]
* Stopping Read required files in advance (for other mountpoints) [ OK ]
* Starting userspace bootsplash [ OK ]
* Stopping cold plug devices [ OK ]
* Stopping userspace bootsplash [ OK ]
* Starting Send an event to indicate plymouth is up [ OK ]
* Stopping log initial device creation [ OK ]
* Stopping Mount network filesystems [ OK ]
* Stopping Read required files in advance (for other mountpoints) [ OK ]
* Stopping Send an event to indicate plymouth is up [ OK ]
* Starting configure network device [ OK ]
* Starting Signal sysvinit that local filesystems are mounted [ OK ]
* Starting configure network device security [ OK ]
* Starting flush early job output to logs [ OK ]
* Starting adb daemon [ OK ]
* Stopping Failsafe Boot Delay [ OK ]
* Starting System V initialisation compatibility [ OK ]
* Stopping flush early job output to logs [ OK ]
* Starting configure virtual network devices [ OK ]
* Stopping System V initialisation compatibility [ OK ]
* Starting system logging daemon [ OK ]
* Starting System V runlevel compatibility [ OK ]
* Starting logrotate 5s check daemon [ OK ]
* Starting save kernel messages [ OK ]
* Starting regular background program processing daemon [ OK ]
* Stopping save kernel messages [ OK ]
dnsmasq: unknown interface wlan0
* Starting OpenSSH server [ OK ]
* Starting DNS forwarder and DHCP server dnsmasq [fail]
* Starting rrwatchdoge daemon [ OK ]
* Stopping System V runlevel compatibility [ OK ]
[ 7.494567] WDIOC_SETFUNCCONFIG: 1
[ 7.499753] WDIOC_SETFUNCCONFIG: 1
Ubuntu 14.04.3 LTS rockrobo ttyS0
rockrobo login:
env print
sunxi#env print
audio_en=1
audio_file=poweron.wav
audio_vol=100
boot_fs=a
boot_normal=ext4load mmc ${fat_num} 40008000 /boot/zImage;bootz 40008000
boot_reason=0x0
boot_ver=2011.09-rc1-dirty
bootcmd=run setargs_mmc boot_normal
bootdelay=3
console=ttyS0,115200
fat_num=2:8
filesize=20
init=/init
location=en
loglevel=7
mmc_root=/dev/mmcblk0p8
partitions=boot-res@mmcblk0p2:env@mmcblk0p5:app@mmcblk0p6:recovery@mmcblk0p7:system_a@mmcblk0p8:system_b@mmcblk0p9:Download@mmcblk0p10:reserve@mmcblk0p11:UDISK@mmcblk0p1
rr_recovery_flag=normal
setargs_mmc=setenv bootargs rootwait boot_fs=${boot_fs} console=${console} root=${mmc_root} rootfstype=ext4 loglevel=${loglevel} partitions=${partitions} boot_reason=${boot_reason} location=${location} boot_ver=${boot_ver}
stderr=serial
stdin=serial
stdout=serial
Environment size: 828/131068 bytes
version
sunxi#version
U-Boot 2011.09-rc1-dirty (Mar 25 2020 - 20:45:43) Allwinner Technology
arm-linux-gnueabi-gcc (Ubuntu/Linaro 4.7.3-12ubuntu1) 4.7.3
GNU ld (GNU Binutils for Ubuntu) 2.24
mmcinfo
sunxi#mmcinfo
Device: SUNXI SD/MMC
Manufacturer ID: 11
OEM: 100
Name: 004GA
Tran Speed: 25000000
Rd Block Len: 512
MMC version 5.0
High Capacity: Yes
Capacity: 3.7 GiB
Bus Width: 4-bit
mmc part
sunxi#mmc part
Partition Map for MMC device 2 -- Partition Type: DOS
Partition Start Sector Num Sectors Type
1 4513792 3268608 b
2 73728 16384 6
3 1 4423680 5 Extd
5 90112 32768 83
6 122880 131072 83
7 253952 1048576 83
8 1302528 1048576 83
9 2351104 1048576 83
10 3399680 1081344 83
11 4481024 32768 83
ext4ls mmc 2:1
sunxi#ext4ls mmc 2:1
<DIR> 4096 .
<DIR> 4096 ..
<DIR> 16384 lost+found
<DIR> 4096 rockrobo
<DIR> 4096 wlan
<DIR> 4096 miio
<DIR> 4096 rriot
ext4ls mmc 2:1
<DIR> 4096 .
<DIR> 4096 ..
<DIR> 4096 lost+found
344813 font24.sft
357443 font32.sft
8838 test_config.fex
6776 test_config.bin
ext4ls mmc 2:6
<DIR> 1024 .
<DIR> 1024 ..
30772 librrafm.so
98 device.conf
16 vinda
<DIR> 1024 roborock
256 roborock.conf.sign
185 roborock.conf
10 adb.conf
ext4ls mmc 2:7
<DIR> 1024 .
<DIR> 1024 ..
<DIR> 12288 lost+found
<DIR> 5120 sbin
<DIR> 1024 usr
<DIR> 1024 sys
<DIR> 1024 opt
<DIR> 1024 run
<DIR> 1024 tmp
<DIR> 1024 media
<DIR> 1024 home
<DIR> 1024 lib
<DIR> 1024 mnt
<DIR> 3072 bin
<DIR> 1024 srv
<DIR> 1024 root
<DIR> 5120 etc
<DIR> 1024 proc
<DIR> 3072 dev
<DIR> 1024 var
<DIR> 1024 boot
ext4ls mmc 2:8
<DIR> 1024 .
<DIR> 1024 ..
<DIR> 12288 lost+found
<DIR> 5120 sbin
<DIR> 1024 usr
<DIR> 1024 sys
<DIR> 1024 opt
<DIR> 1024 run
<DIR> 1024 tmp
<DIR> 1024 media
<DIR> 1024 home
<DIR> 1024 lib
<DIR> 1024 mnt
<DIR> 3072 bin
<DIR> 1024 srv
<DIR> 1024 root
<DIR> 5120 etc
<DIR> 1024 proc
<DIR> 3072 dev
<DIR> 1024 var
<DIR> 1024 boot
ext4load
ext4load - load binary file from a Ext4 filesystem
Usage:
ext4load <interface> <dev[:part]> [addr] [filename] [bytes]
- load binary file 'filename' from 'dev' on 'interface'
to address 'addr' from ext4 filesystem
mmc dev
sunxi#mmc dev
mmc2(part 0) is current device
On Shutdown
wait-for-state stop/waiting
haveged: haveged Stopping due to signal 15
* Stopping rsync daemon rsync [ OK ]
* (not running)
* Asking all remaining processes to terminate... [ OK ]
* All processes ended within 1 seconds... [ OK ]
umount: /tmp: device is busy.
(In some cases useful info about processes that use
the device is found by lsof(8) or fuser(1))
* Unmounting temporary filesystems... [fail]
* Deactivating swap... [ OK ]
* Unmounting local filesystems... [ OK ]
* Will now halt
[ 216.968322] [MCU_UART] sent ap poweroff event to mcu